Features: - The Best worth 1S toothpick PNP Kit in the market; - Only 19.5gram 1s Toothpick; - Smooth and Powerful; - Runcam Nano 3 FPV Camera; - Comes unassemble, Just Plug to build it, do not need solder, enjoy DIY Fun Specification: ( Assemble Guide ) Item Name: 80mm F4 1S FPV Racing Drone; Wheelbase: 80mm; Size: 69mmx69mmx29mm (without propeller); Weight: 19.5g (without battery). 0802 19000KV Brushless Motor: Mode: 0802 19000KV; Configu-ration: 9N12P; Stator Diamter:8mm; Stator Length: 2mm; Shaft Diameter: Φ1.5mm; Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm; Weight(g): 1.8g; No.of Cells(Lipo): 1S only. HQProp 40mm 2-Blade Propeller: Model: Micro Whoop 40mmx2; Item Name: 40mm 2-Blade Propeller; Propeller Diameter: 40mm; Pitch: 1; Blades: 2; Material: Poly Carbonate; Hub Diameter: 5mm; Hub Thickness: 5mm; Shaft: 1.5mm; Color: Gray; Quantity: 2 CW + 2 CCW ( in same color); Weight: 0.24g. CRAZYBEE F4 Lite AIO Flight Controller: Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR; (Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS; MCU: STM32F411CEU6 (100MHZ, 512K FLASH); Sensor: MPU-6000(SPI connection); Board size: 28.5 * 28.5MM; Power supply: 1S battery input (DC 2.9V-4.35V); Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready; Built-in Betaflight OSD(SPI Control); Built-in 5.8G VTX; Built-in SPI Frsky/Flysky/DSMX/DSMX receiver; Built-in 5V 1A BEC; Built-in voltage detection. Onboard 5A 4in1 ESC: MCU upgraded to EFM8BB21; Power supply: 1S LiPo/LiPo HV; Current: 5A continuous peak 6A (3 seconds); Support BLHeliSuite programmable; Factory firmware: O_H_5_REV16_7.HEX; Default protocol: DSHOT600. Onboard Frsky Receiver (Optional): SPI BUS receiver Frsky D8 Compatible; Compatible Non EU transmitter D8 model; Channels: 8CH; Failsafe support; No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m. Onboard Flysky Receiver  (Optional): SPI BUS receiver; Protocol: AFHDS and AFHDS-2A Switchable; Channels: 8ch(AFHDS) or 14ch(AFHDS-2A); No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m; Failsafe support. Onboard 5.8G VTX: Output power: 25mw; Frequency: 40CH; Input voltage: 3.3V 5.5V; Current consumption: 300mA(type); Frequency: 5.8GHz 5bands 40 channels; With Race band; Smartaudio ready. Runcam Nano 3 FPV Camera: Image Sensor: 1/3″ CMOS; Horizontal Resolution: 800TVL; Lens: 2.3mm(M6.5) FOV 140°; Signal System: NTSC; S/N Ratio: >50dBElectronic Shutter Speed: Auto; Auto Gain Control (AGC): Auto; Min. Illumination: 0.01Luxat1.2F; D-WDR: Auto; Day/Night: Color; Power:DC 3-5.5V; Current: 110mAat5V 120mAat3.3V; Housing Material: ABS; Net Weight: 1.2g; Dimensions: L14mm*W14mm*H9mm. Recommend Lipo Battery ( NOT Included): 1S 250mAh, around 3:40mins; 1S 300mAh, around 4:30mins.